Electronics Test Centre
NVLAP Lab Code: 200282-0
Address and Contact Information:
302 LEGGET DRIVE, UNIT 100OTTAWA ON K2K 1Y5
CANADA
Contact: Mr. Dan Zanette
Phone: 613-599-6800
Fax: 613-599-7614
E-Mail: dan.zanette@etc-mpb.com
Send E-Mail to Laboratory: Electronics Test Centre
URL: http://www.etc-mpb.com
NVLAP Accreditation Information
Listed below is the scope of accreditation for this laboratory as of February 10, 2012. For additional information, contact NVLAP at (301) 975-4016.Send E-Mail to NVLAP at: NVLAP@nist.gov
Electromagnetic Compatibility & Telecommunications
Accreditation Valid From: October 1, 2011 Through: September 30, 2012
[12/C01]
MIL-STD-462 Version C Method CE01
- Emissions Test Methods
[12/160D21] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 21 - Emission of Radio Frequency Energy
[12/160F21] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 21 - Emissions of Radio Frequency Energy
[12/50121cc] EN 50121-3-2 (2006)
Railway applications - Electromagnetic compatibility -- Part 3-2: Rolling stock - Apparatus
[12/50121e] EN 50121-2 (2006)
Railway applications - Electromagnetic compatibility -- Part 2: Emission of the whole railway system to the outside world
[12/50121f] EN 50121-3-1 (2006)
Railway applications - Electromagnetic compatibility -- Part 3-1: Rolling stock - Train and complete vehicle
[12/50121g] EN 50121-4 (2006)
Railway applications - Electromagnetic compatibility -- Part 4: Emission and immunity of the signalling and telecommunications apparatus
[12/55012] CISPR 12 (2001), EN 55012 (2002) & BS EN 55012 (2002)
Vehicles, boats and internal combustion engine driven devices - Radio disturbance characteristics
[12/60E213] RTCA DO-160E
Section 21.3, RF Emissions, Conducted
[12/60E214] RTCA DO-160E
Section 21.4, RF Emissions, Radiated
[12/61000g] EN 61000-6-3 (2007)
Electromagnetic compatibility (EMC) - Part 6-3: Generic standard - Emission standard for residential, commericial and light industrial environments
[12/C37] IEEE Std C37.90.1 (2002)
Surge Withstand Capability (SWC) Tests for Relays and Relay Systems Associated with Electric Power Apparatus
[12/C37a] IEEE Std C37.90.2
Standard for withstand capability of relay systems to radiated electromagnetic interference from transceivers design tests
[12/C37b] IEEE Std C37.90.3 (2001)
Electrostatic Discharge Tests for Protective Relays
[12/C62b] IEEE Std C62.41 Ring Wave (1991)
IEEE Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits
[12/CIS11]
IEC/CISPR 11 + A1 (1997), EN 55011 (1998), AS/NZS CISPR 11 (2002), and CNS 13803 (1997): Limits and Methods of Measurement of Electromagnetic Disturbance Characteristics of Industrial, Scientific, and Medical Radio-Frequency Equipment
[12/CIS11g] IEC/CISPR 11, Ed. 4.1 (2004-06)
Industrial, scientific and medical (ISM) radio-frequency equipment - Electromagnetic disturbance characteristics - Limits and methods of measurements
[12/CIS12] CISPR 12 (2001)
Vehicles, boats and internal combustion engine driven devices - Radio disturbance characteristics
[12/CIS14d] IEC/CISPR 14-1 (2001) and A1 (2001)
Electromagnetic Compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emissions
[12/CIS14e] EN 55014-1 (2001) and A1 (2001)
Electromagnetic Compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
[12/CIS15] IEC/CISPR 15 (2000) + A1 (2001)
Limits and methods of measurements of radio disturbance characteristics of electrical lighting and similar equipment
[12/CIS15a] AS/NZS CISPR 15 (2002)
Limits and methods of measurements of radio disturbance characteristics of electrical lighting and similar equipment
[12/CIS15c] EN 55015 (2000) + A1 (2001)
Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment
[12/CIS22] IEC/CISPR 22 (1997) & EN 55022 (1998) + A1(2000)
Limits and methods of measurement of radio disturbance characteristics of information technology equipment
[12/CIS22a] IEC/CISPR 22 (1993) and EN 55022 (1994)
Limits and methods of measurement of radio disturbance characteristics of information technology equipment, Amendment 1 (1995) and Amendment 2 (1996)
[12/CIS22b] CNS 13438 (1997)
Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment
[12/CIS22i] IEC/CISPR 22, Edition 5.2 (2006-03)
Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipment
[12/DCE01] DEF-STAN 59-41 Part 3, DCE01 (1995-10)
Conducted Emission on Primary Power Lines
[12/DCE02] DEF-STAN 59-41 Part 3, DCE02 (1995-10)
Conducted Emission on Control Signal and Power Lines
[12/DCE03] DEF-STAN 59-41 Part 3, DCE03 (1995-10)
Exported Transients Power Lines
[12/DRE01] DEF-STAN 59-41 Part 3, DRE01 (1995-10)
Radiated Emissions E Field
[12/DRE02] DEF-STAN 59-41 Part 3, DRE02 (1995-10)
H Field Radiation
[12/DRE03] DEF-STAN 59-41 Part 3, DRE03 (1995-10)
Radiated Emissions Installed Antenna
[12/DS59411] Defense Standard 59-411 Part 3 Issue 1:2007 + Amdt 1
Electromagnetic Compatibility Test Methods and Limits for Equipment and Sub Systems
[12/EM02a]
IEC 61000-3-2, Edition 2.1 (2001-10), EN 61000-3-2 (2000), and AS/NZS 2279.1 (2000): Electromagnetic compatibility (EMC) Part 3-2: Limits - Limits for harmonic current emissions (equipment input current <= 16 A)
[12/EM02b] IEC 61000-3-2, Second Edition (2000-08)
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current<= 16 A per phase)
[12/EM02c] BS EN 61000-3-2, Ed. 2 (2001); IEC 61000-3-2, Ed. 2 (2000)
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current up to and including 16 A per phase)
[12/EM02i] IEC 61000-3-2, Ed. 3.0 (2005-11)
Electromagnetic compatability (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current <=16 A per phase)
[12/EM03] IEC 61000-3-3(1995); EN 61000-3-3(1995); AS/NZS 2279.3(1995)
EMC - Part 3: Limits - Section 3. Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current up to 16A
[12/EM03b] IEC 61000-3-3, Edition 1.1(2002-03) & EN 61000-3-3, A1(2001)
EMC - Part 3-3: Limits - Limitations of voltage changes, voltage flucuations and flicker, in public low-voltage supply-systems, for equipment with rated current <=16 A per phase and not subject to conditional connections
[12/EM03c] IEC/EN 61000-3-3 (1994) with Amendment 1 (2001)
Conducted Emissions, Voltage Flicker
[12/EM03d] IEC/EN 61000-3-3 (1995) + A1 (2001)
Conducted Emissions, Voltage Flicker
[12/FCC15b1] ANSI C63.4 (2003) with FCC Method 47 CFR Part 15, Subpart B
Unintentional Radiators (up to 6.5 GHz only)
[12/FCC15c] ANSI C63.4 (2003) with FCC Method 47 CFR Part 15, Subpart C
Intentional Radiators
[12/IEE299b] IEEE Std 299 (1997)
Measuring the Effectiveness of Electromagnetic Shielding Enclosures-Description
[12/T51a] AS/NZS CISPR 22 (2004)
Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
[12/VCCIa] VCCI
Agreement of Voluntary Control Council for Interference by Information Technology Equipment - Technical Requirements: V-3/2005.04
- Immunity Test Methods
[12/160D05] RTCA/DO-160D (19997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 5: Temperature
[12/160D06] RTCA/DO 160-D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 6: Humidity
[12/160D15] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 15 - Magnetic Effect
[12/160D16] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 16 - Power Input
[12/160D17] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 17 - Voltage Spike
[12/160D18] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 18 - Audio Frequency Conducted Susceptibility - Power Inputs
[12/160D19] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 19 - Induced Signal Susceptibility
[12/160D20] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 20 - Radio Frequency Susceptibility (Radiated and Conducted)
[12/160D20b] RTCA/DO-160 (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 20.6: Radio Frequency Susceptibility (Radiated Mode Tuned)
[12/160D22] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 22 - Lightning Induced Transient Susceptibility
[12/160D25] RTCA/DO-160D (1997)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 25 - Electrostatic Discharge (ESD)
[12/160F15] RTCA/DO 160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 15 - Magnetic Effect
[12/160F16] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 16 - Power Input
[12/160F17] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 17 - Voltage Spike
[12/160F18] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 18 - Audio Frequency Conducted Suspceptibility - Power Inputs
[12/160F19] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 19 - Induced Signal Susceptibility
[12/160F20] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 20 - Radio Frequency Susceptibility (Radiated and Conducted)
[12/160F22] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 22 - Lightning Induced Transient Susceptibility
[12/160F23] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 23 - Lightning Direct Effects
[12/160F25] RTCA/DO-160F (2007)
Environmental Conditions and Test Procedures for Airborne Equipment - Section 25 - Electrostatic Discharge (ESD)
[12/50121d] EN 50121-1 (2006)
Railway applications - Electromagnetic compatibility - Part 1: General
[12/501304] EN 50130-4 (1996)
Alarm systems - Part 4. Electromagnetic compatibility - Product family standard: Immunity requirements for components of fire, intruder and social alarm systems
[12/60E05] RTCA DO -160E
Section 5: Temperature
[12/60E06] RTCA DO-160E
Section 6: Humidity
[12/60E15] RTCA DO 160E
Section 15, Magnetic Effects
[12/60E16] RTCA DO160E
Section 16, Power Input
[12/60E17] RTCA DO-160E
Section 17, Voltage Spikes
[12/60E18] RTCA DO-160E
Section 18, Audio Frequency Conducted Susceptibility
[12/60E19] RTCA DO-160E
Section 19, Induced Signal Susceptibility
[12/60E204] RTCA DO-160E
Section 20.4, RF Susceptibility, Conducted
[12/60E205] RTCA DO-160E
Section 20.5, RF Susceptibility, Radiated
[12/60E206] RTCA DO-160E
Section 20.6: RF Susceptability (Radiated Mode Tuned)
[12/60E22] RTCA DO-160E
Section 22, Lightning Induced Transient Susceptibility
[12/60E25] RTCA DO-160E
Section 25, Electrostatic Discharge (ESD)
[12/610006j] EN 61000-6-2 (2005)
Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments
[12/61000k] EN 61000-6-1 (2007)
Electromagnetic compatibility (EMC) - Part 6 - 1: Generic standards - Immunity for residential, commercial and light-industrial environments
[12/61326j] IEC 61326-2-6, Ed. 1.0 (2005-12)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-6: Particular requirements - In vitro diagnostic (IVD) medical equipment
[12/CIS14i1] EN 55014-2 (1997)
Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 2. Immunity - Product family standard
[12/CIS24a] EN 55024 and CISPR 24 (1997, modified)
Information technology equipment - Immunity characteristics - Limits and methods of measurements
[12/CIS24c] EN 55024 (1998) and A1 (2001)
Information technology equipment - Immunity characteristics - Limits and methods of measurement
[12/EM03ii] IEC 61000-3-3, Edition 1.2
EMC- Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low- voltage supply systems, for equipment with rated current <= 16 A per phase and not subject to conditional connection
[12/I01] IEC 61000-4-2, Ed. 1.2 (2001); EN 61000-4-2
Electrostatic Discharge Immunity Test
[12/I02] IEC 61000-4-3, Ed. 2.0 (2002-03); EN 61000-4-3 (2002)
Radiated Radio-Frequency Electromagnetic Field Immunity Test
[12/I02g] IEC 61000-4-3, Ed. 3.0 (2006-02)
Electromagnetic compatibility (EMC) - Part 4-3: Testing measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
[12/I03] IEC 61000-4-4(1995), A1(2000), A2(2001); EN 61000-4-4
Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical Fast Transient/Burst Immunity Test
[12/I03c] IEC 61000-4-4, Ed. 2.0 (2004-07)
Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test
[12/I04] IEC 61000-4-5, Ed. 1.1 (2001-04); EN 61000-4-5
Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test
[12/I04b] IEC 61000-4-5 (2001), A1(2000); EN 61000-4-5(2001), A1(2000)
Surge Immunity Test
[12/I04c] IEC 61000-4-5, Ed 1.1 (2005-11)
EMC - Part 4-5: Testing and measurement techniques - Surge immunity test
[12/I05] IEC 61000-4-6, Ed. 2.0 (2003-05); EN 61000-4-6
Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
[12/I05f] IEC 61000-4-6, Ed 2.0 (2006-05)
EMC - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
[12/I06] IEC 61000-4-8, Ed. 1.1 (2001); EN 61000-4-8
Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
[12/I07] IEC 61000-4-11, Ed. 1.1 (2001-03); EN 61000-4-11
Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests
[12/I07c] IEC 61000-4-11, Ed. 2 (2004-03) & EN 61000-4-11
Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests
[12/I12a] IEC 61000-4-12, 2nd edition (2006-09)
EMC - Part 4-12: Testing and measurement techniques - Ring wave immunity test
[12/IEC407] IEC 61000-4-7, Ed 2.0 (2002-08)
Immunity to conducted disturbances
[12/IEC409] IEC 61000-4-9, Ed 1.1 (2001-03)
EMC - Part 4-9: Testing and Measurement Techniques - Pulse Magnetic Field Immunity Test
[12/IEC410] IEC 61000-4-10, Ed 1.1 (2001-03)
EMC - Part 4-10: Testing and measurement techniques - Damped oscillatory magnetic field immunity test
[12/IEC414] IEC 61000-4-14, Edition 1.1 (2002-07)
EMC - Part 4-14: Testing and Measurement Techniques - Voltage Fluctuation Immunity Test
[12/IEC416] IEC 61000-4-16, Edition 1.1 (2002-07)
EMC - Part 4-16: Testing and Measurement Techniques - Test for Immunity to Conducted, Common Mode Disturbances in the Frequency Range 0 Hz to 150 kHz
[12/IEC417] IEC 61000-4-17, Edition 1.1 (2002-07)
EMC - Part 4-17: Testing and Measurement Techniques - Ripple on d.c. Input Power Port Immunity Test
[12/IEC420] IEC 61000-4-20, Edition 1.1 (2007-01)
EMC – Part 4-20: Testing and measurement techniques – Emission and immunity testing in transverse electromagnetic (TEM) waveguides
[12/IEC421] IEC 61000-4-21, 1st Edition (2003-08)
EMC-Part 4-21: Testing and measurement techniques Reverberation chamber test methods
[12/IEC428] IEC 61000-4-28, Edition 1.1 (2002-07)
EMC - Part 4-28: Testing and Measurement Techniques - Variation of Power Frequency, Immunity Test
[12/J111301] SAE J1113/1 (2006-10)
Procedures and Limits for Components of Vehicles, Boats, and Machines (except Aircraft)
[12/J111302] SAE J1113-2 (1996-09)
Electromagnetic compatibility measurement procedures and limits for vehicle components (except aircraft) - Conducted immunity, 30 Hz to 250 kHz - all leads
[12/J111303] SAE J1113-3 (2006-09)
Direct Injection of Radio Frequency Power
[12/J111304] SAE J1113-4 (2004-08)
Immunity to Radiated Electromagnetic Fields - Bulk Current Injection (BCI) Method
[12/J111311] SAE J1113-11 (2006-01)
Immunity to Conducted Transients on Power Leads
[12/J111312] SAE J1113-12 (2006-08)
Electrical Interference by Conduction and Coupling
[12/J111313] SAE J1113-13 (2004-11)
Electromagnetic Compatibility Measurement Procedure for Vehicle Components - Part 13 - Immunity to Electrostatic Discharge
[12/J111321] SAE J1113/21 (1998-01)
Road Vehicles - Electrical disturbances by narrowband radiated electromagnetic energy - Component test methods - Part 21 - Absorber-Lined Chamber
[12/J111322] SAE J1113-22 (2003-11)
Immunity Radiated Magnetic Fields
[12/J111323] SAE J1113/23 (1995-09)
Electromagnetic Compatibility Measurement Procedure for Vehicle Components - Immunity to Radiated Electromagnetic Fields, 10 kHz to 200 MHz, Strip Line Method
[12/J111324] SAE J1113/24
Immunity to radiated electromagnetic fields; 10 kHz to 200 MHz - Crawford TEM cell and 10 kHz to 5 GHz - Wideband TEM cell
[12/J111325] SAE J1113-25 (2005-07)
Immunity to Radiated Electromagnetic Fields (Tri-Plate Line Method)
[12/J111326] SAE J1113-26 (2006-05)
Immunity to AC Power Line Electric Fields
[12/J111327] SAE J1113-27 (2005-09)
Mode Stir Reverberation Chambers (S3 and S5 Under Construction)
[12/J111328] SAE J1113-28 (2004-11)
Immunity to Radiated Electromagnetic Fields- Reverberation Chambers (Mode Tuning) (S3 and S5 Under Construction)
[12/J111341] SAE J1113/41 (2000-05)
Limits and methods of measurement of radio disturbance characteristics of components and modules for the protection of receivers used on board vehicles
[12/J111342] SAE J1113-42 (2006-10)
EMT-Component Test Procedure - Part 42- Conducted Transient Emission
[12/J1113a] SAE J1113-21 (2005-10)
Immunity to Electromagnetic Fields, Absorber Lined Chamber
[12/J1113b] SAE J1113-23 (2002-10)
Immunity Radiated Magnetic Fields, Strip Line Method
[12/J1113c] SAE J1113-41 (2006-09)
Radio Disturbance Characteristics for the Protection of Receivers Used on Board Vehicles
[12/M1275b] MIL-STD-1275B (November 20, 1997)
Characteristics of 28 Volt DC Electrical Systems in Military Vehicles
- MIL-STD Test Methods
[12/C03]
MIL-STD-462 Version C Method CE03
[12/C06]
MIL-STD-462 Version C Method CE06
[12/C07]
MIL-STD-462 Version C Method CE07
[12/C10]
MIL-STD-462 Version C Method CS01
[12/C11]
MIL-STD-462 Version C Method CS02
[12/C12]
MIL-STD-462 Version C Method CS03
[12/C13]
MIL-STD-462 Version C Method CS04
[12/C14]
MIL-STD-462 Version C Method CS05
[12/C15]
MIL-STD-462 Version C Method CS06
[12/C16]
MIL-STD-462 Version C Method CS09
[12/C17]
MIL-STD-462 Version C Method CS10
[12/C18]
MIL-STD-462 Version C Method CS11
[12/C21]
MIL-STD-462 Version C Method CS14
[12/MIL462] MIL-STD-462: 1967 with Notices 1, 2, 3, 4, 5, 6
Military Standard, Electromagnetic Interference Characteristics, Measurement of. Notice 1:1968; Notice 2:1970; Notice 3: 1971; Notice 4:1980; Notice 5:1986; Notice 6:1987
(CE03, CE04, RE02, RS03)
[12/MS461A] MIL-STD-461A
Electromagnetic Interference Characteristics Requirements for Equipment (CE03, CE04, RE02, RS03)
[12/RE01]
MIL-STD-462 Version C Method RE01
[12/RE02]
MIL-STD-462 Version C Method RE02
[12/RE03]
MIL-STD-462 Version C Method RE03
[12/RS01]
MIL-STD-462 Version C Method RS01
[12/RS02]
MIL-STD-462 Version C Method RS02
[12/RS03]
MIL-STD-462 Version C Method RS03
- MIL-STD-462 : Conducted Emissions
[12/A01]
MIL-STD-462 Method CE01
[12/A04]
MIL-STD-462 Method CE02
[12/A06]
MIL-STD-462 Method CE03
[12/A08]
MIL-STD-462 Method CE04
[12/A10]
MIL-STD-462 Method CE06
[12/A12]
MIL-STD-462 Method CE07
[12/A13]
MIL-STD-462 Version D Method CE101
[12/A14]
MIL-STD-462 Version D Method CE102
[12/A15]
MIL-STD-462 Version D Method CE106
[12/A16]
MIL-STD-461 Version E Method CE101
[12/A17]
MIL-STD-461 Version E Method CE102
[12/A18]
MIL-STD-461 Version E Method CE106
[12/A19]
MIL-STD-461 Version F Method CE101
[12/A20]
MIL-STD-461 Version F Method CE102
[12/A21]
MIL-STD-461 Version F Method CE106
- MIL-STD-462 : Conducted Susceptibility
[12/B01]
MIL-STD-462 Method CS01
[12/B02]
MIL-STD-462 Method CS02
[12/B04]
MIL-STD-462 Method CS03/CS04/CS05
[12/B05]
MIL-STD-462 Method CS06
[12/B06]
MIL-STD-462 Method CS07
[12/B07]
MIL-STD-462 Method CS09
[12/B08]
MIL-STD-462 Method CS10
[12/B09]
MIL-STD-462 Method CS11
[12/B10]
MIL-STD-462 Method CS12
[12/B11]
MIL-STD-462 Method CS13
[12/B12]
MIL-STD-462 Version D Method CS101
[12/B13]
MIL-STD-462 Version D Method CS103
[12/B14]
MIL-STD-462 Version D Method CS104
[12/B15]
MIL-STD-462 Version D Method CS105
[12/B16]
MIL-STD-462 Version D Method CS109
[12/B17]
MIL-STD-462 Version D Method CS114
[12/B18]
MIL-STD-462 Version D Method CS115
[12/B19]
MIL-STD-462 Version D Method CS116
[12/B20]
MIL-STD-461 Version E Method CS101
[12/B21]
MIL-STD-461 Version E Method CS103
[12/B22]
MIL-STD-461 Version E Method CS104
[12/B23]
MIL-STD-461 Version E Method CS105
[12/B24]
MIL-STD-461 Version E Method CS109
[12/B25]
MIL-STD-461 Version E Method CS114
[12/B26]
MIL-STD-461 Version E Method CS115
[12/B27]
MIL-STD-461 Version E Method CS116
[12/B28]
MIL-STD-461 Version F Method CS101
[12/B29]
MIL-STD-461 Version F Method CS103
[12/B30]
MIL-STD-461 Version F Method CS104
[12/B31]
MIL-STD-461 Version F Method CS105
[12/B32]
MIL-STD-461 Version F Method CS106
[12/B33]
MIL-STD-461 Version F Method CS109
[12/B34]
MIL-STD-461 Version F Method CS114
[12/B35]
MIL-STD-461 Version F Method CS115
[12/B36]
MIL-STD-461 Version F Method CS116
- MIL-STD-462 : Radiated Emissions
[12/D01]
MIL-STD-462 Method RE01
[12/D02]
MIL-STD-462 Method RE02
[12/D03]
MIL-STD-462 Method RE03
[12/D04]
MIL-STD-462 Version D Method RE101
[12/D05]
MIL-STD-462 Version D Method RE102
[12/D06]
MIL-STD-462 Version D Method RE103
[12/D07]
MIL-STD-461 Version E Method RE101
[12/D08]
MIL-STD-461 Version E Method RE102
[12/D09]
MIL-STD-461 Version E Method RE103
[12/D10]
MIL-STD-461 Version F Method RE101
[12/D12]
MIL-STD-461 Version F Method RE103
- MIL-STD-462 : Radiated Susceptibility
[12/E01]
MIL-STD-462 Method RS01
[12/E02]
MIL-STD-462 Method RS02
[12/E03]
MIL-STD-462 Method RS03 (Consult laboratory for field strengths available)
[12/E04]
MIL-STD-462 Method RS03 employing RADHAZ procedures for high level testing (Consult laboratory for field strengths available)
[12/E07]
MIL-STD-462 Method RS06
[12/E08]
MIL-STD-462 Version D Method RS101
[12/E09]
MIL-STD-462 Version D Method RS103
[12/E11]
MIL-STD-461 Version E Method RS101
[12/E12]
MIL-STD-461 Version E Method RS103
[12/E15]
MIL-STD-461 Version F Method RS101
[12/E16]
MIL-STD-461 Version F Method RS103
[12/E17]
MIL-STD-461 Version F Method RS105
- Product Safety Test Methods
[12/4117] AS/NZS 4117 (1999)
Surge protective devices for telecommunications applications
[12/606011] IEC 60601-1-2, Ed. 2.0 (2001) + A1 (2004)
Medical electrical equipment - Part 1-2: General requirements for safety - Collateral standard: Electromagnetic compatibility - Requirements and tests
[12/60601a] IEC 60601-1-2, Ed1(1993);Ed2(2001-09); JIS T0601-1-2(2002.7)
Medical electrical equipment - Part 1 and Part 1-2: General requirements for safety: Collateral standard: EMC - Requirements and tests
[12/60601aa] IEC 60601-1-2, Ed 2.1 (2004-11) & EN 60601-1-2 (2002)
Medical electrical equipment - Part 1-2: General requirements for safety - Collateral standard: Electromagnetic compatibility - Requirements and tests
[12/60601e] IEC 60601-1-1 (2000-12), 2nd edition
Medical electrical equipment - Part 1-1: General requirements for safety - Collateral standard: Safety requirements for medical electrical systems
[12/T41h] UL 60950-1 (2003)
Safety- Part 1- General Requirements For Information Technology Equipment
[12/T50a] AS/NZ 60950 (2000)
Safety of information technology equipment
- Radio Test Methods
[12/301489b] ETSI EN 301 489-3 v1.4.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters; ElectroMagnetic Compatibility standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 40 GHz
[12/31489] ETSI EN 301 489-1 v1.4.1 (2002-08)
Electromagnetic Compatibility and Radio Spectrum Matter (ERM); Electromagnetic Compatibility (EMC) Standard for Radio Equipment and Services; Part 1: Common Technical Requirements
[12/31489ac] ETSI EN 301 489-1 V1.8.1 (2008-04)
ERM; ElectroMagnetic Compatibilty (EMC); Standard for Radio Equipment and Services; Part 1: Common Technical Requirements
- Telecommunications Test Methods
[12/1089a] GR-1089-CORE, Issue 3 (October 2002)
Electromagnetic Compatibility and Electrical Safety - Generic Criteria for Network Telecommunications Equipment (sections 2, 3.3, and 3.5)
[12/1089b] GR-1089-CORE, Issue 3 (October 2002)
Electromagnetic Compatibility and Electrical Safety - Generic Criteria for Network Telecommunications Equipment (sections 3.2 and 3.4)
[12/1089g] GR-1089-CORE, Issue 4 (June 2006)
Electromagnetic Compatibility and Electrical Safety - General Criteria for Network Telecommunications Equipment
[12/300386a] EN 300 386 V1.2.1 (2000-03)
Electromagnetic compatibility and radio spectrum matter (ERM); Telecommunication network equipment; Electromagnetic Compatibility (EMC) requirements
[12/300386f] ETSI EN 300 386 V1.3.3 (2005-04)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Telecommunication network equipment; ElectroMagnetic Compatibility (EMC) requirements
[12/FCC22G] 47 CFR FCC Part 22 Subpart G
Air-Ground Radiotelephone service
Return to NVLAP Program Listing